Sikafloor®-359 N
Sikafloor®-359 N is a two part tough-elastic, coloured, non-yellowing, polyurethane seal coat.
- Tough-elastic
- Good mechanical and chemical resistance
- Watertight
- Good opacity
- Non-yellowing
- Matt finish
- Easy application
- Slip resistant surface possible
Usage
- Abrasion resistant seal coat with high mechanical resistance for broadcast systems with crack-bridging properties in industrial flooring
- Particularly suitable for car park decks, ramps and warehouses etc.
Advantages
- Tough-elastic
- Good mechanical and chemical resistance
- Watertight
- Good opacity
- Non-yellowing
- Matt finish
- Easy application
- Slip resistant surface possible
Packaging
Part A | 25.35 kg containers |
Part B | 7.15 kg containers |
Part A+B | 32.5 kg ready to mix units |
Colour
Resin - Part A | coloured, liquid |
Hardener - Part B | transparent, liquid |
Please contact Sika for colour shade selection.
Product Details
ENVIRONMENTAL INFORMATION
Sikafloor®-359N is listed on the Eco-Product Directory as environmentally friendly product choice for green building initiatives. (application no.: PL-01564-2023)
APPROVALS / STANDARDS
- Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 02080104002500000011008, certified by notified factory production control certification body 0921, and provided with the CE marking.
- Coating for surface protection of concrete according to EN 1504-2:2004, Declaration of Performance 02080104002500000011008, certified by notified factory production control certification body 0921, and provided with the CE marking.
- Certified as part of the Surface Protection System OS 11a according to DIN EN 1504-2 and DIN V 18026.
- Certified as part of the Surface Protection System OS 11b according to DIN EN 1504-2 and DIN V 18026.
Chemical Base
Polyurethane
Shelf Life
12 months from date of production
Storage Conditions
The product must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions. Protect from direct sunlight.
Density
Part A | ~ 1.67 kg/litre |
Part B | ~ 1.05 kg/litre |
Mixed resin | ~ 1.45 kg/litre |
All Density values at +23 °C
Solid Content by Weight
~ 85 %
Solid Content by Volume
~ 85 %
Shore D Hardness
~ 52 (7 days / +23 °C) | (DIN 53 505) |
Abrasion Resistance
160 mg (CS 10/1000/1000) (7 days / +23 °C) | (DIN 53 505) |
Tensile Adhesion Strength
> 1.5 N/mm2 (failure in concrete) | (EN 13892-8) |
Chemical Resistance
Resistant to many chemicals. Contact Sika technical service for specific information.
Application
Mixing Ratio
Part A : Part B = 78 : 22 (by weight)
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperature | Time |
+10 °C | ~ 40 minutes |
+20 °C | ~ 25 minutes |
+30 °C | ~ 15 minutes |
Curing Time
Before applying Sikafloor®-359 N on Sikafloor®-375/ -350 N/ -326/ -261 broadcast allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 24 hours | * |
+20 °C | 12 hours | * |
+30 °C | 6 hours | * |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
* Not applicable as the product will be applied on the structured surface provided by the quartz sand.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~ 48 hours | ~ 5 days | ~ 10 days |
+20 °C | ~ 24 hours | ~ 3 days | ~ 7 days |
+30 °C | ~ 16 hours | ~ 2 days | ~ 3 days |
Note: Times are approximate and will be affected by changing ambient conditions
Consumption
~ 0.7–0.9 kg/m2/layer. Please refer to the respective System Data Sheet.
MIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved.
For the addition of quartz sand: When parts A and B have been mixed, add the quartz sand 0.1–0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.
Mixing Tools:
Sikafloor®-359 N must be thoroughly mixed using a low speed electric stirrer (300–400 rpm) or other suitable equipment.
APPLICATION
Prior to application, confirm substrate moisture content, relative humidity and dew point. As a seal coat, the product can be applied by squeegee and then back-rolled (crosswise) with a short-piled roller.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.