Product Data Sheet Show all documents

SikaInject®-865

Fast Setting Micro-Fine Portland Cement for Rock and Soil Injection

SikaInject®-865 is a well-graded cement with fast setting-time, milled from pure Portland cement clinker with Blaine value ~650 m2/kg

  • Initial and final setting faster than standard micro-fine cements
  • Small particle size = very good penetration into fine joints, fissures and pores
  • Providing a water-tight grouted rock or soil mass
  • Increases the productivity in injection operations
  • Short open-time = reduction of waiting-time until next excavation round to a minimum
Talk to Our Experts
Product Data Sheet Show all documents

Usage

  • Pre-excavation grouting in underground structures 
  • Post injection
  • Water ingress reduction
  • Ground stabilization
  • Contact injection
 

Advantages

  • Initial and final setting faster than standard micro-fine cements
  • Small particle size = very good penetration into fine joints, fissures and pores
  • Providing a water-tight grouted rock or soil mass
  • Increases the productivity in injection operations
  • Short open-time = reduction of waiting-time until next excavation round to a minimum

Packaging

20 kg bags 1000 kg big-bags

Product Details

Product Information

Chemical Base

Fineness (Blaine) > 625 m2/kg  Particle size distribution: <40 micron 100 % <30 micron 99 % <20 micron 97 % <15 micron 93 % <10 micron 80 % < 5 micron 50 % < 2 micron 23 % d95 16 microns d50 5 microns d25 2 microns

Shelf Life

9 months when stored in original closed bags in ventilated dry areas

Storage Conditions

Ventilated dry areas, closed original bags

 

Application

Application Information

Flowability

Injection grout properties indicated below, relates to a mix containing a High-Range-Water-Reducing-Admixture

(e.g. 1.5% Sika Viscocrete):

  • Water/cement ratio 1.0

  • Mud balance 1.48 – 1.50 kg/l

  • Flow cone 32 – 34 s

  • Bleeding maximum 2 %

Pot Life

The mix should be kept under constant agitation prior to injection. Do not keep the grout in the agitator longer than 30 – 40 minutes.

Initial Set Time

60 min - 120 min (Vicat needle up to 6 mm +/- 3 mm, over ground)

Final Set Time

120 min - 150 min (Penetration by Vicat needle, 1 mm)

Setting times at 1:1 w/c ratio (by weight), 20°C

Finishing Time

SikaInject®-865 will have set sufficiently after 2 - 2½ hours to allow drilling for control or blast holes
Application steps

MIXING

Use SikaInject®-865 always with 0.6 % – 2 % High Range Water Reducing Admixture (Sika Viscocrete), related to cement weight. To prove compatibility, it is recommended to do a pretest in regards of bleeding/segregation. W/C ratio (weight) should be 0.6 - 1.0.

  • Fill mixer with water

  • Add cement while running mixer

  • Mix for 2 min more

  • Add the High Range Water Reducing Admixture and mix 1 min

  • Transfer to agitator

 

Note:

  • Use efficient mixer; colloidal mixers with >1500 rpm give best results

  • Do not over-mix

  • Mixing longer than recommended may cause temperature-increase and grout set in pump and/or hoses

APPLICATION

  • Typically high-pressure piston pumps are used to pump the suspension into the rock

  • Inject grout within 30 - 40 minutes after mixing to ensure that it keeps spreading into fissures

  • Longer open times can be achieved by using SikaTard hydration-control stabilizer-admixture 

  • For much longer open times use SikaInject®-865 SR, available upon special request

 

Documents