Sikasil® Pool
Sikasil® Pool is a one component, neutral curing silicone sealant for use in swimming pools and permanently wet areas.
- Very good water resistance
- High chlorine resistance
- Very good resistance to fungal attack
- Non-corrosive
- High elasticity and flexibility
Usage
Sikasil® Pool is designed for joints in and around swimming pools, areas under permanent water immersion and frequently wet areas, such as shower rooms in gyms, between tiles, concrete, glass and metals.Advantages
- Very good water resistance
- High chlorine resistance
- Very good resistance to fungal attack
- Non-corrosive
- High elasticity and flexibility
Packaging
300 ml cartridges, 12 cartridges per box
Colour
White, grey
Product Details
Chemical Base
Neutral Cure Silicone
Shelf Life
Sikasil® Pool has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Storage Conditions
Sikasil® Pool shall be stored in dry conditions, protected from direct sunlight.
Density
1.05 kg/l approx. | (ISO 1183-1) |
Shore A Hardness
~20 approx. (after 28 days) | (ISO 868) |
Tensile Strength
~1.5 N/mm2 approx. | (ISO 8339) |
Secant Tensile Modulus
~0.30 N/mm2 approx. at 100% elongation (23 °C) | (ISO 8339) |
Movement Capability
± 25% | (ISO 9047) |
Elastic Recovery
> 90% approx. | (ISO 7389) |
Tear Propagation Resistance
~4.0 N/mm approx. | (ISO 34) |
Service Temperature
−40 °C to +80 °C
Joint Design
The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be 10 mm to 15 mm. Minimum depths or thicknesses not less than 6 mm .
For larger joints please contact our Technical Service Department.
Application
Sag Flow
< 2 mm (20 mm profile, 23 °C) | (ISO 7390) |
Ambient Air Temperature
+5 °C to +40 °C
Substrate Temperature
+5 °C to +40 °C
min. 3°C above dew point temperature
Backing Material
Use closed cell, polyethylene foam backing rods.
Curing rate
~2.0 mm/24 hours approx. (23 °C / 50% r.h.) | (CQP 049-2) |
Skin Time
~5 minutes approx. (23 °C / 50% r.h.) | (CQP 019-1) |
Consumption
Joint length [m] per 300 ml cartridge | Joint width [mm] | Joint depth [mm] |
3.5 | 10 | 8 |
2 | 15 | 10 |
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil® Pool adheres without primers and/or activators.
However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pre-treatment procedures shall be followed:
Non-porous substrates
Aluminium, anodised aluminium, stainless steel, glass, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel, or Sika® Aktivator-100 wiped on and off with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours).
Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205 wiped on with a clean towel, or Sika® Aktivator-100 wiped on and off with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30 minutes (< 8 hours) before sealing the joints.
PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).
Porous substrates
Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).
For more detailed advice and instructions please contact the local Sika Technical Services Department.
Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly.
CLEANING OF TOOLS
Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured the residual material can only be removed mechanically.